Community Brag Posts

Here is a pretty simple shelf I built for my closet. Left it backless b/c I wear a 12 1/2 and needed my shoes to be able to hang out back a bit. The top 2 I am using for folded tshirts I don't hang, like undershirts and tank tops.

Material List:
1- 1x10x10 -$13.00 (2 side boards)
2- 1x10x6 - $8.00x2=16 (6 shelves)
24 1 1/4 pocket screws. Had these on hand, could sub for 1 1/2 wood screws if you do not have pocket scew jig set.

Tools:
Tape measure
Quick Square
Miter saw ( which I used) or a Circular saw
Drill

Cut list
*2-59.9+- side boards

*The 1x10x10 was exactly 10ft long, so I marked off 5 feet with a line. Then I just cut on the line with the miter saw. This left me with 2 equal boards. Lets say 59.9 give or take a MM or so. Doesnt matter as long as they are even. If you mess the cut up, stack them on top of each other and recut to equal.

*6-23.9+- Shelves

*Again the 1x10x6 was exactly 6ft, so I made 2 lines, one at 2ft, the next at 4ft. Split them when cutting, and had 3 equal boards. Size can be smaller if you like, this is how I did it.

Now the fun part, and probably second longest time consuming part, behind drilling pocket holes.

I took the 2 side boards and clamped them so they would be flush and even side by side. (both face down side to side so you have one clamped board of 1x20x59.5 so to speak) I used my quick square to mark off .75(thickness of shelf boards). Start at the bottom or top, draw line. then,start next at 11 inches, step and repeat.In the end should have 5 shelves exactly 11 inches apart.

I next predrilled my 6 shelf boards with 2 pocket screw holes on each side, about 3 1/2 inches from each edge. This was most time consuming, you could use 1 1/2in screws and go from side boards into shelf boards and save time, also if you don't have pocket hole jig.

Assembling, I started at bottom, attached side boards to both side of bottom shelf, and worked my way up.The lines you pre-drew act as marker for next shelf,and help a ton when trying to keep everything square. The last one,top part, should be snug to put in. I find its best to do this way as everything keeps square as long as you have straight lumber.

Cost overall-$30.00 since I had screws, total time was around 2 hours to complete, and this was me having to explain everything to the little one lol

I'm loving the finish on this, and it's a useful little project.

Table was fun to build and put our own spin on it. Great project for my wife and I. Took a few days to complete and begin using. Table dimensions we builst are 7' by 3.5' exactly as we needed for or dining room.

I made two different versions and reversed side the ladders were on. I learned from the mistakes I made on the first bed and the second one came together a little easier.

I left them natural and the girls will pick a paint color in the spring.

Although I can sew, my wife made both sets of mattresses along with a bunch of doll clothes.

I guess I never got around to sharing my finished chair! I'm almost ashamed to...1) because it was so long ago when I made it and 2) because everyone else's looks so great!

I made this bed for my 4 year old. It was my first project. Took a lot longer than I thought it would, but I'm really pleased with how it turned out!

I modified the original plans to make the table narrower and lighter weight for my narrower patio. To do this, I used 1x8 (qty 4) pine boards on the top. The legs were cut at 29.25" to achieve the 30" height. The cross pieces were cut at 25.5". This gave me a 29" wide table. I went with a wood prep application, stainable wood filler, stain (Minwax Special Walnut), and 3 coats of spar urethane (for UV protection). The wood filler reacted with the wood prep and turned orange. I had to sand it out and redo it. Lessons we learn along the way! The brown table with the black chairs coordinates with all of my patio furniture. I am ready to host a dinner party around the pool! Thank you Ana White!

Ana's simple, cheap and easy console table, made entirely with repurposed and scrap wood, so it was free! The plan was great, and it was easy to adjust to the wood I had on hand. The distressed finish was fun to do too.

This was our first Ana White project. We knew we wanted to do a table, and decided this was the easiest one for first-timers without a kreg jig (YET!). We made things even SIMPLER by having Lowe's do ALL the cutting for us! I didn't even know they would do that, but they will.... and happily so!

The project went VERY well and we are delighted with our new table. We used Rustoleum "Kona" stain and we used Rustoleum spray gloss poly because Lowes had a bunch of cans of it on clearance. We were happy with the results, though it may not be the best indoor product in the future ;-)

The project took us about 4-6 hours to build, and then we just sanded a little each evening, and the next weekend we stained and poly.

My daughter and I dedicate this doll house to my great uncle George Breeding who made a beautiful doll house for my sister when we were kids. I hope my kids will carry the maker bug into the next generation! Great plans!

This project is all about using a Kreg Jig. My daughter asked for some shadowboxes to go around her chalkboard. 1 piece of 3/4" plywood and a few 1x2's later - here it is. It's really just an 8' x 2' box with the window panes inside - super simple, but does require a compact drill. Mounted to the wall using a ledger board underneath, then, pocket holes in the top shelf to join it to the studs. Quite sturdy. One day I'll learn Sketch-Up well enough to make this into a plan.

Made from scrap wood left in the empty lots besides me, from framing crews.

Cost me just the time, screws, sand paper and stain.

Made all the cuts with a skillsaw, by saving the $$$ I have now went and bought a mitre and table saw. YAY!

This was a fun afternoon project built almost entirely from materials I already had on hand. I finished it off with a coat of Gunstock stain by Minwax, followed by a coat of Cherry stain. I sanded a little between each coat. Next I applied a thin coat of black paint and sanded gently until the stain started to show through (and bare wood in places). Finally I applied a coat of polyurethane gloss. It took about four days to complete the finish and I made it up as I went along. Super happy with the end result. I opted not to add the side bins, but I did add an extra 2x2 on each side, mostly because the 2x2 I used for the legs was a little bowed and the exta piece ensured that they'd stay where they're supposed to.